Diagnostics - Parking Light Flash Table
Flashes
3 slow flashes^
4
5 Slow
5 Fast
6
10
1 —pause —
1—pause —
5 flashes
1 - pause - 2
ON SOLID for 3
seconds^.
ON continuously
ON continuously
ON 2 seconds
ON 4 seconds
ON 20 seconds
Continuous flashes
25 seconds
Description
Doors locked, starter kill armed.
Run time has expired.
TRUNK button pressed.
Start signal received by the module.
Cold weather mode cancelled.
Doors unlocked, starter kill disarmed.
Remote start attempt cancelled by remote.
Exiting ignition valet.
Exiting remote valet.
Power-up reset.
Entering cold weather mode.
Extended run time.
Entering ignition valet.
Entering remote valet.
_______
.after a failed start attempt
The module did not detect a tach signal.
+12 V detected on the brake input wire either while cranking or during run time.
Entering multi-speed tach programming.
Start attempt failed because no tach signal has been programmed.
Tach signal programmed.
A remote start was attempted while a tach-before-crank signal was detected before cranking.
Unit reset see “Resetting the Module” (p.1)
A ground (-) signal was detected on the hood pin input wire.
• Transmitter has been programmed.
[During the transmitter programming procedure]
There was a remote start attempt while the vehicle was in valet mode.
Failed start: vehicle’s low battery voltage.
_________________________
..followed by 1 flash
..followed by 3 flashes
Exiting cold weather mode
Entering cold weather mode
Idle mode: Idle mode is engaged
Run time: The vehicle has been remote started and is in run time.
While the brake
pedal is
pressed.
• Confirms that cold weather mode is engaged
The hood has been opened and a ground (-) signal has been detected on the hood pin input
wire.
Locking or unlocking a door (with Door pulses configured to 4 sec.)
The hood pin has been flashed and you are now in the programming centre.
Panic mode is activated.
To obtain a copy of the installation guide,
please visit the
http://www.autostart.ca website and
click on the « Download » tab.
P. 8 http://www.autostart.ca
Installation Guide
AUTOMATIC TRANSMISSION REMOTE STARTER
AS-1735
Quick Installation Guide
To obtain a copy of the installation guide,
please visit the http://www.autostart.ca website
click on the u Download » tab.
and
Tab/e of Contents
How to Flash the Hood Pin.....................1
Resetting the Module
..............................
1
Transmitter Programming Procedure
.....
1
Entering Programming Options
.............
2
Programming Options.............................2
Tach Programming
..................................
6
Horn Honk Timing....................................6
How to Flash the Hood Pin
Supplementary Information
....................
6
Fifth Relay Output....................................6
Tach jumper settings...............................6
Testing
......................................................
7
Diagnostics - Parking Light Flash
Table..........................................................8
THE INSTALLER > THE MODULE >
• Press and hold the hood pin for 4 seconds.
• Release the hood pin.
• While the parking lights are on, press down the hood pin once more
and release the hood pin immediately, before the parking lights turn off.
• You now have 20 seconds to select one of the sub-menus
Parking Lights “ON”
“ON” for 20 seconds
Resetting the Module
WARNING! By resetting the module, all programmed values are erased — i.e.: tach, transmitter as well as programming
options. The programming options are returned to their default values.
1. Flash the hood pin (see above).
2. Once having reached the programming mode, the system will grant 10 seconds to complete the next step:
a) Press and release the break pedal 6
times
(within 10 seconds from entering programming mode).
The parking lights will flash 8 times to confirm the module is reset.
Transmitter Programming Procedure
1. Flash the hood pin (see on page 1) —^ the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, turn the ignition key to the ignition on (run) position and immediately to the OFF position.
3. Press and hold the lock button and keep it down until the parking lights flash 5 times quickly.
4. The transmitter has been stored in memory.
5. To exit: close the hood.
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be
that either damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices
supplied. Please note that this guide has been written for properly trained Autostart technicians: a certain level of skills and
knowledge is therefore assumed. Please review the installation guide carefully before beginning any work.
Warning
This remote starter is designed for vehicles with an automatic transmission only. Before installing the unit, test that the
vehicle does not start when the gear select lever is in the “Drive” position. If it starts in gear, install a manual-transmission
remote starter system instead.
DOC.1.00
- September 6, 2006 DL Lp
Manufactured in Canada by Autostart
2
3
8
(4 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern